Page 533 - Cornwell Product Catalog
P. 533

 DOLLIES & SPOONS
  FA1052
Spoon Dolly
Long handle permits many uses in places otherwise inaccessible. 􏰀an be dri􏰁en between reinforcements and outer panel, then used to pry outward as the metal is dinged. 􏰂􏰃cellent forming and caulking tool for the deep pockets of doors, 􏰄uarter􏰅panels, rear fenders and lower trunk panels. Length 􏰆􏰇􏰅􏰇􏰈􏰉􏰊, 􏰋ead 􏰌i􏰍e􏰎 􏰏􏰅􏰆􏰈􏰏 􏰃 􏰆􏰊 􏰃 􏰇􏰊. 􏰐eight􏰎 􏰉.􏰏 lbs.
FA1036
Light Dingi
􏰑o ding ridges smooth and le􏰁el. 􏰐hen held against ridge and struck with hammer, it spreads blow o􏰁er large area making it a smooth 􏰒ob and pre􏰁enting damage to metal or finish. 􏰓ot made for prying. 􏰔􏰁erall Length􏰎 􏰆􏰕􏰊, Face􏰎 􏰏􏰊 􏰃 􏰉􏰅􏰖􏰈􏰆􏰗􏰊, 􏰐eight􏰎 .􏰖􏰕 lbs.
LS51880
Spot Weld Chisel, 180 Degree
Dri􏰁e the blade with a hammer from the top or the side through the panel. 􏰠anels are separated without damage. 􏰑he blade is sharpened on three sides and offset for clearance.
SLAPPING FILES
Formed files for panel shrinking
and metal remo􏰁al. 􏰌haped for easy hand use. Fully heat treated.
TE89360
5 Piece Body Forming Punch Set
􏰑hese punches fit where your hammer will not. 􏰝reat for tight clearance spots, cre􏰁ices and corners. 􏰑he punch surfaces are polished and hardened
to form sheet metal with precision in hard􏰅to􏰅reach areas. For use on􏰎 Door panels, high crown panels, interior parts of body panels, fenders, rear quarter panels, trunk lids and frames. 􏰀omes with 􏰖 of the most popular profiles and shapes to fit the 􏰒ob.
INCLUDES:
SM20046
Panel Shaper Kit
􏰘n air hammer dri􏰁en set of three self
lubricating nylon reinforced heads to
easily access deep reach areas and
badly deformed sheet metal surfaces
to form them back to original shapes.
􏰑hree uni􏰄ue head shapes with arbors
allow each tool to be attached to an
air hammer to fi􏰃 body lines, conca􏰁e
areas and flat surfaces. 􏰀hisel head
works with door, body lines, corner shaping and fender edges. 􏰙ounded head straightens out wheel house and 􏰄uarter panels. Flat head straightens out floors, trunk floors and pro􏰁ides stress relief in the repair process.
SM20047 Re􏰄la􏰚ement C􏰛isel 􏰜ead
SM20048 Re􏰄la􏰚ement Rounded 􏰜ead
SM20049 Re􏰄la􏰚ement 􏰝lat 􏰜ead
SM20000
Pull Rod Set
􏰌uper tough alloy steel is precisely heat treated for ma􏰃imum strength. 􏰠lastic handle is comfortable to use. 􏰡se two at a time for pulling. 􏰜nstruction sheet included.
INCLUDES:
 ng Spoon
 PART NUMBER
  TYPE
  OVERALL LENGTH
   TE89361
 Round Body Forming Punch
   12"
   TE89362
Square Body Forming Punch
  12”
 TE89363
 Bumping Body Forming Punch
 12"
 TE89364
  Offset Bumping Body Forming Punch
  12”
   TE89365
 Radial Chisel Body Forming Punch
   12”
       PART NUMBER
   TYPE
   CUT
   SH77505
 Medium
 2nd Cut
 SH77506
   Coarse
   Bastard Cut
      SEAM BUSTERS
􏰂asily separate spot welded or bonded panels. 􏰌a􏰁e up to 􏰆􏰖 minutes per panel replacement. For 􏰄uarter panels, rockers and any other pinchweld. 􏰌harpened on two edges 􏰞􏰑he sharp end allows for penetration between the panels and the side edge allows for side impact to dri􏰁e the panels apart without damage􏰟. 􏰌uper tough alloy steel. 􏰀ushioned handle absorbs shock.
 QTY.
   PART NUMBER
   DESCRIPTION
   4
 SM20001
 Pull Rods with formed shank
 2
  SM20002
  Pick Pulls with straight shank
 1
   SM20003
   Stainless Steel Straight Edge
   1
  SM20004
  HS Split Point Drill Bit
    PART NUMBER
   DESCRIPTION
   SM20015
 Straight Seam Buster
 SM20016
   Right Angle Seam Buster
   See page 640 for safety warnings.
WWW.CORNWELLTOOLS.COM
  531
METAL WORKING
  PAINT & BODY






   531   532   533   534   535